2SA1145 DATASHEET PDF

2SAO(TE6,F,M) Toshiba Bipolar Transistors – BJT Transistor PNP V A datasheet, inventory, & pricing. 2SA datasheet, 2SA pdf, 2SA data sheet, datasheet, data sheet, pdf, TOSHIBA, TRANSISTOR SILICON PNP EPITAXIAL TYPE (PCT PROCESS). Package. TO TO MOD. TO TO Pc(W). Ta°c). NicmA). – VCEOVA. 2SC 2SA 2SC

Author: Mihn Zoloramar
Country: Puerto Rico
Language: English (Spanish)
Genre: Politics
Published (Last): 3 August 2011
Pages: 203
PDF File Size: 19.63 Mb
ePub File Size: 16.19 Mb
ISBN: 571-1-97332-893-9
Downloads: 37244
Price: Free* [*Free Regsitration Required]
Uploader: Faunos

Return to dynahi headphone amplifier. The output transistors are from BG Electronics and are said to datasgeet Toshiba I can have a closer look on them and maybe post a picture here You do not have the required permissions to view the files attached to this post. Your board has them both facing the same direction. Turned around the JFETs on one board, checked all soldering joints again and proceded as per Ti’s advice. Now the bias for the output transistors dstasheet through the roof with about 5V across the poor 20R resistors I just left it one for a few seconds and am wondering now whether I have fake output transistors.

I have attached an image and compared it to what I found on the net What do you guys think? Next question will be where to find genuine Toshiba ones I assume my 2SC are fakes as dataheet. Have you tried the second board yet? Does it exhibit the same problem? That’s why I disconnected it from power when I switched the amp on the first time a few days ago, see previous post. To be honest I never ever had a part fail in any datwsheet my builds before which are many, incl.

  ALJ 13001 PDF

КАСКАД : электронные компоненты и другая электроника : Документация

I could provide a datsaheet high res images If I see correctly the center hole looks like someone drilled it in the molded body after it was made. The surface inside the hole doesn’t look like it came from the molding machine. I had both amp boards biased to.

When I went back to tweak the bias settings for off set, one channel was 2sa1154. I suspect I shorted one of the 2SC’s to ground, but don’t know yet. The other board is finished. Another problem is I grossly under estimated the heat sink for the power supply. I was measuring around F.

New heat sink came today and it’s 2sa11455 4 times bigger! I’m not an expert on fakes but your 2SA’s appear a bit different than mine.

2SA1145 Datasheet, Equivalent, Cross Reference Search

I can’t see your 2SA well enough to make a judgement. A few things to consider. Some people have reported problems with biasing there amps.

  LE GRAND MENAGE RAFFA PDF

I think Ti recommends to ohm resistors instead of the ohm’s that parallel the 2 pots. I used ohms. With these resistors, I have to turn my pots better than half way to get. Also, make sure you have the pots turned to max resistance counter clockwise on my build before you start.

I really suspect that you blew the the 2SA’s and the 2SA’s from your prior dtasheet. I measured the resistance between my bad board and the good board and found only slight datashret.

I am going to pull a few to be certain. I’m also wondering about the heat your 20 ohm resistors are generating.

Even on my bad board, mine run cool. Make sure that none of them is shorted to ground on the top side. I doubt if that’s the problem, but it don’t cost anything to check. It’s more likely your output devices are fighting each other for a lack of better words. Board index Time zone: